The Lower Strings
Here is a way to tie the strings for the larger gauge
strings. You don't need a string tie for this since the string should
be thick enough to hold it in place. If the knot
comes through the grommet, you'll have to use a string end. Make
sure it is stiff enough so as not to bend as you tighten the loop.
This video will show you how to tie this knot using the
|Looking at the drawing on the right, loop your string so
it looks just like the picture. You'll need to make the second
loop opposite from the first loop so that it makes a mirror image.
Make sure the "smile" is in the front. Also think of
the longer side of the string on the left and the shorter end
on the right. The left end will be the side that
actually goes into the harp and up to the tuning pin.
|From the back of the first loop, put the second loop through the
|Pull the LEFT end of the string tight. I have drawn it a little
loose, but you pull yours tight. That's all you need to do.
You can then thread your string into the hole in the back
of the harp and up to the tuning pin (see the first helpful hint for
an easier way). If the red end stick didn't turn then it is apt to fall
out while you thread the string through the hole.
All of the below is on the string
tying as well.
Tying the string onto the tuning
Now that you’ve got the knot tied at the end of the string, you’ll
need to thread it through the tuning pin. Here’s what I do to
cinch the knot on this end. This works for all strings but the bass
wires (see below for these strings).
Line up the hole of the tuning pin so that it is vertical. Standing
behind the harp, thread the string through the hole (it should be going
straight up through the hole in the tuning pin) and pull it back towards
Then slip the string below the tuning pin and between the wooden neck
of the harp and the string you just threaded up through the tuning pin.
You will be pushing the string toward the front of the harp now.
Bring it up between the tuning pin you’re stringing and the tuning
pin of the string one note below and pull it out away from the harp.
Begin tuning up the string. The first wind should catch around the
end of the string. Make sure your winds go toward the neck of the
harp as you tune (unless your pins are the type of pin that wants
you to make the winds go away from the neck. I believe Tripplet pins
are like this). Try to get a straight line from the tuning pin to the
bridge pin, especially in the bass wires.
Using the cutters of the needle nose pliers, cut off all of the extra
string to avoid any buzzing and to keep your harp tidy.
The Bass Wires
Pull the bass wire all the way through the tuning pin
straight up. Cut it off 2-2 1/2" above the tuning pin. Push
it back down so it is ALMOST flush with the tuning pin, just barely
sticking out (less than the width of the string). Begin winding the
slack around the tuning pin until you have it to pitch. This method
helps to cut down on sharp edges cutting you or your case.
Tuning up new strings
New strings will need to stretch before they will hold a pitch for any
length of time. You might want to over tune the string about 20-50 cents
and then stretch it a little. It will again fall way below pitch. Do
this a couple of times being careful not to stretch or over tune it
too much or it may break. If you are in the middle of a performance,
you’ll need to get it to hold pitch before you play so keep talking
to the audience while you stretch and tune, stretch and tune.
I hope this has helped to get you on your way to tying harp strings.
If you have questions, come to one of my workshops at the next confernce,
visit our booth or call me and I'll help you out. If you already have
a way that works for you, or if you find a better way, wonderful!
Trouble Shooting Some String
Continued String Breakage
If the string breaks continually at the point of contact with the tuning
pin, you might have a sharp edge where the string goes through the hole.
To compensate for this, you can leave about a 1/2-1inch of slack before
tuning up the string. This eases the point where it is sharp and usually
takes care of the problem. And you can turn the tuning pin over so the
sharp edge is on the other side.
The same might be true for strings that break at the soundboard. The
bottom of the grommet may be cutting the string below the soundboard.
To help this situation, put a leather washer between your string knot
and the soundboard. You will need to put the washer on before you
tie the string. You can get leather washers from Robinson's String
Shop in California. (619 473-8556). If the string is breaking right
above the soundboard you may need a new grommet, also available from
Robinson's although you'll need to know if your grommet is small,
medium, or large and if it is regular or heavy duty (they are not interchangeable).
If your string pops off the
If there are too many winds of the string on the tuning pin, it may
cause it to pop off the bridge pin. As the string stretches and
tunes up to pitch, you may acquire more windings on the tuning pin
then you want. The string is at too steep of an angle to the bridge
pin and when you lever that string, it pops off the bridge pin. The
solution is to completely unwind the string until it is going straight
up out of the hole of the tuning pin. Pull it up through the tuning
pin about 1/2 inch, re-wind the string and tune it back up. Cut off
the extra 1/2 inch of string. This should take at least 1 wind out
of the string and it should stay on the bridge pin.
If your tuning pins slip
Sometimes a tuning pin will slip due to changes in humidity. Most tuning
pins are tapered like violin tuning pins. The pin gets larger in diameter
on the side that the tuning key fits into. If you have a tapered tuning
pin that keeps slipping, de-tune the string about a half of a turn and
then as you turn the pin to tune the string back up, push the pin in.
You should provide counter pressure by bracing the neck of the harp
with your left hand, while pushing in with the key in your right.
You can also check the angle of the string to the neck. If the string
angles towards the neck from the tuning pin, it could be putting back
pressure on the tuning pin and pushing it out of the hole. This is
more likely to happen in the low bass wires. The remedy here is to
detune the string and stretch out the windings so they run straight
up and down instead of at an angle. If there aren't enough windings,
you probably have to put on a new string. Cut your string about 2" longer than the
string length you need to allow for the extra windings.
The above tips and helpful hints are specifically taylored
for Thormahlen Harps.
Just wanted to let you know I was sending you thanks as you helped
me re-string a broken string this afternoon. Katie had forgotten
to make a copy of directions for me and she suggested I check your
website. I was thrilled to see not only directions but drawings as
I struggled with that wiley string!!! The directions were clear,
I got the string on without breaking it and played just to make sure
that it stayed on. And yes, the Q tip stick worked great. I love my harp
(still!!) and appreciate it everytime I look at it. Paula Caron Grantham,
Some suggestions on tuning
your harp, back to the strings page
or on to the page About Harps.